Deprecated: Methods with the same name as their class will not be constructors in a future version of PHP; plgSystemNiceUserInfoLite has a deprecated constructor in /home/ddsystem/public_html/ on line 28
Turbochargers vs Superchargers Comparison


Perfect Power Articles.


Talk to two people, and you will get three different answers. Here are some considerations in deciding which one is the right choice for you:

Turbochargers fit easily on straight 4 or 6 cylinder engines. They must be fitted as close as possible to the head.

Turbochargers run very hot, just short of melting down. Therefore, the Turbocharger surrounding must be well insulated from the radiating heat. It is advisable to idle the engine for a minute or two after heavy use before switching off. Turbochargers are water-cooled.

Turbochargers run hot because they rely on the exhaust gas velocity, which is directly proportional to the temperature.

Turbochargers have turbo lag, i.e. the time it takes to wind the "fan" up. This is less noticeable with automatics or during manual gearshift, but very noticeable during a "standing start".

Turbochargers are used more frequently in Europe because smaller engines (4 cylinders) are more common.

Turbochargers require a special exhaust branch, which must be made of high temperature material. And if possible with no heat expansion! Otherwise your exhaust branch gasket will not last.

You can fit two Turbochargers on a V6 or V8, it will work, but you must choose the type of Turbochargers carefully. You also need to consider that you'll have twice the radiation heat problem and twice the cost.

Superchargers are used mainly on petrol engines, seldom on diesel engines.

Another way to explain a Turbo's lag is that a Turbocharger works on the chain reaction principle. It is the starting of the chain which produces the lag. Let's assume the engine idles and so does the turbo. The boost pressure is ZERO. Then you open the throttle to a particular point and keep it there. The engine operates in a decompressed state and produces very little power. The little power it makes raises the exhaust gas temperature and velocity. This makes the turbo spin a little faster and raises the boost pressure, which in turn makes a little more power, which in turn..... (the chain reaction sets in). The chain reaction is limited by the waste gate regulation, and the airflow through the butterflies. Modern electronic units (XMS4, SMT8, SMT8L, and SMT8T) can regulate the boost pressure.

Depending on the type of Supercharger you are considering, the fitting varies from being almost impossible to as easy as fitting an air-conditioner pump.

Turbochargers are used on constant load engines such as trucks, marine engines and power-plants.

There are many types of Superchargers, but only one type of Turbocharger, if you generalize. The selection of the correct size and manufacturer of either Turbocharger or Supercharger is an art, which should be left to the experts. Many technical books have been written about it and free advice is available from the manufacturers of Turbochargers or Superchargers.

When you look at the boost pressure curve of Turbochargers and Superchargers, the Superchargers don't look too impressive. This is because they produce a more ‘constant’ pressure curve. This results in very good drive-ability.

Because the Turbocharger comes short in the ‘drive-ability’ department (but looks good in peak power) modern turbo installations use a boost regulation process, which ‘flattens’ the power curve and increases the drive-ability.

Non-decompressed engines and advanced turbo control further enhance the drive-ability of a turbocharger. This can be performed by any of the following products: XMS4, SMT8, SMT8L, and SMT8T.

It is safe to say that the latest advances in turbo technology make it equal to a supercharger. The preferences in drive system and under bonnet space are important.

Superchargers are more predictable in engineering terms. From the manufacturer's data you can choose the correct gearing for the desired boost pressure and RPM.
Superchargers are more expensive and difficult to manufacture.

Superchargers heat the boost air to the same extent as a Turbocharger.


If you have a straight engine, not used in a dragster, consider installing a Turbocharger. Turbochargers are less expensive, but require some engineering. Alternatively, you can consider a Supercharger. Do some market research as to the type, size, lubrication, cooling and gearing required. If you are building a dragster, you should install a Supercharger. Most Supercharger manufacturers offer kits and provide very helpful advice.