ACCESSORIES

Perfect Power offers the following accessories to

be used with the range of Perfect Power Units.


     
     
 

RUBBER BOOT

Perfect Power Water Resistant Cover - Rubber Boot

   
  This accessory will be used as a protective cover against dust and liquids (waterproof). For use on the following units : SMT8-L, SMT6, SMT8L Wireless, E-Tune, SMT8-T, 2.5 Bar AMP Sensor, I-Switch and the Perfect Power Oxygen Clamp.
   
   
     
     
     
     
 

AIR-TEMP

Perfect Power AIR-TEMP Temperature Sensor

   
  Air Temperature Sensor. Perfect Power's Air Temperature sensor is a must for boosted applications. Turbo and Supercharger installations aren't complete without this little guy. Small and easy to fit. NTC or negative temperature coefficient type.
   
   
     
     
     
     
 

AMP-2

Perfect Power 2.5 Bar Manifold Pressure Sensor

   
  2.5 Bar Manifold Pressure Sensor. Manifold Pressure Sensor 2.5 Bar. Good for 1.5 bar boost pressure. Convenient 12 Volt power connection.
   
   
     
     
     
     
 

AMP-3

Perfect Power AMP-3 3 Bar Manifold Pressure Sensor

   
  3 Bar Manifold Pressure Sensor. Good for 2.0 bar boost pressure. Supplied together with 5 Volt Regulator.
   
   
     
     
     
     
 

ENG-TEMP

Perfect Power ENG-TEMP Engine Temperature Sensor

   
  Engine Temperature Sensor. Perfect Power's Engine Temperature Sensor is small and easy to fit. NTC or negative temperature coefficient type.
   
   
     
     
     
     
 

IGN-AMP

Perfect Power IGN-AMP 7 Amp Ignition Amplifier

   
  7 Amp Ignition Amplifier for injectors or coils, has a heat sink for dissipating heat for higher power applications. Easy to install.
   
   
     
     
     
     
 

OXYGEN CLAMP

Perfect Power Oxygen Clamp

   
  Narrow Band Lambda clamp for de-cat applications.
   
   
     
     
     
     
 

SMT6 SHORTING PLUG

Perfect Power SMT6 Shorting Plug

   
  Shorting Plug for the SMT6 piggyback chip. Will revert the installation to standard.
   
   
     
     
     
     
 

SMT8-L SHORTING PLUG

Perfect Power SMT8-L Shorting Plug

   
  Shorting Plug for the SMT8-L piggyback chip. Will revert the installation to standard.
   
   
     
     
     
     
 

SMT8-T SHORTING PLUG

Perfect Power SMT8-T Shorting Plug

   
  Shorting Plug for the SMT8-T piggyback chip. Will revert the installation to standard.
   
   
     
     
     
     
 

TRIGGER WHEEL 60

Perfect Power Trigger Wheel 60

   
  60 tooth trigger wheel made from mild steel. Outside diameter of 170mm.
   
   
     
     
     
     
 

TRIGGER WHEEL 24+1 54mm

Perfect Power Trigger Wheel 24+1 54mm

   
  24+1 tooth trigger wheel made from stainless steel. Outside diameter of 54mm. Replacement trigger wheel for some Nissan distributors.
   
   
     
     
     
     
 

TRIGGER WHEEL 24+1 50mm

Perfect Power Trigger Wheel 24+1 50mm

   
  24+1 tooth trigger wheel made from stainless steel. Outside diameter of 50mm. Replacement trigger wheel fro some Nissan distributors.
   
   
     
     
     
     
 

TRIGGER WHEEL 36W

Perfect Power Trigger Wheel 36W

   
  36 tooth trigger wheel made from mild steel. Outside diameter of 100mm.
   
   
     
     
     
     
 

MAGNETIC CRANK SENSOR

Perfect Power Magnetic Crank Sensor

   
  Magnetic Crank angle sensor with 2 signal wires in a screen.
   
   
     
     
     
     
 

5 VOLT REGULATOR

Perfect Power 5 Volt Regulator

   
  5 Volt regulator to power throttle position sensors or manifold pressure sensors. Also supplied with a 3 Bar Manifold Pressure Sensor - AMP-3.
   
   
     
     
     
     
 

USB CABLE

Perfect Power USB Cable

   
  USB Communication Cable - See our new Ferrite Cores for use with the USB cable.
   
   
     
     
     
     
 

SMT8-T COMM CABLE

Perfect Power SMT8-T Communication Cable

   
  SMT8-T Communication Cable XY-PC13.
   
   
     
     
     
     
 

RS232 COMM CABLE

Perfect Power RS232 Communication Cable

   
  RS232 communication cable for MIC3, PRS and XMSV3 Stand Alone Units.
   
   
     
     
     
     
 

FERRITE CORE

Perfect Power Ferrite Cores

   
  Ferrite Cores are for noise reduction on the USB Cable and to help stop interference with the communication on the USB Cable and the LetRipp II Software and unit. We suggest you purchase two of these cores for either end of the USB cable. A ferrite core is a passive electric component used to suppress high frequency noise in electronic circuits and we have found them most useful when we have experienced interference between the unit and software through the USB Cable.
   
   
     
     
     
     
 

USB MINI CABLE

Perfect Power USB Mini Cable

   
  Mini USB Communication Cable